No edit summary |
|||
| Line 14: | Line 14: | ||
</gallery> |
</gallery> |
||
| − | *paper (at least 18 sheets of A4 size office paper that has already been used on one side, i.e. "scrap paper"). |
+ | *[[paper]] (at least 18 sheets of A4 size office paper that has already been used on one side, i.e. "scrap paper"). |
| − | *cotton thread |
+ | *[[cotton]] thread |
| − | *sewing needle |
+ | *[[sewing needle]] |
| − | *scissors |
+ | *[[scissors]] |
| − | *PVA glue (craft/wood glue) |
+ | *[[PVA glue]] (craft/wood glue) |
| − | *fabric for binding (plain fabric) |
+ | *[[fabric]] for binding (plain fabric) |
*plastic bag |
*plastic bag |
||
| − | * |
+ | *large [[binder clip]] |
| − | *thick cardboard (eg. old cardboard box) |
+ | *thick [[cardboard]] (eg. old cardboard box) |
*fabric for cover (nice-looking fabric) |
*fabric for cover (nice-looking fabric) |
||
Revision as of 06:17, 21 May 2006
IMAGES COMING SOON
Method I
This method teaches you how to make a book out of paper that has already been used on one side, however the technique could easily be adapted to use new paper.
Method I: What you need
- paper (at least 18 sheets of A4 size office paper that has already been used on one side, i.e. "scrap paper").
- cotton thread
- sewing needle
- scissors
- PVA glue (craft/wood glue)
- fabric for binding (plain fabric)
- plastic bag
- large binder clip
- thick cardboard (eg. old cardboard box)
- fabric for cover (nice-looking fabric)
Method I: Quick Steps
1. Get the pages ready.
2. Sew the pages into little bundles.
3. Glue the bundles together with a piece of fabric along the spine.
4. Cut the cover-cardboard and cover-fabric to size.
5. Glue the spine-protector to the cover fabric.
6. Attach the cover-cardboard.
7. Cover the book with fabric.
Method I: Full Steps
Stage 1 - Getting the pages ready.
1. Fold each page in half so the unwanted-text is hidden.
2. Fold each page in half again.
3. Slide 3 folded pieces of paper together. Repeat for all the pieces of paper.
Stage 2 - Sewing the signatures (i.e. sewing the pages into little bundles).
1. Open up each little bundle of pages at the centre page.
2. Lay the bundle of pages, face down on a soft surface (eg. carpet).
3. Thread a sewing needle with cotton thread. Double the thread over and tie a knot in the end.
4. Push the needle through the bundle of pages from the outside of the fold.
5. Turn the bundle of pages over and pull the needle and cotton thread through.
6. Push the needle through the bundle of pages from the inside of the fold.
7. Turn the pages over again and loop the needle through the knot at the end of the cotton thread (so the thread is anchored).
8. Do a few more stitches and then tie off the thread.
9. Stitch each bundle of pages together in the same manner.
Stage 3 - Gluing the signatures together along the spine (i.e. gluing the bundles together along the spine)
1. Stack all the sewn bundles of paper neatly on top of each other.
2. Clip them together with a big strong stationery clip, on the non-spine side.
3. Cut a piece of plain fabric the same size as the stack of pages.
4. Put PVA glue along the spine of the pages. Rub it with your finger-tip so that it covers the spine evenly.
5. Glue the spine to the middle of the piece of plain fabric. Press the fabric with your finger-tip so that it is firmly against the spine of the pages.
6. Hold the fabric firmly in place, and move the stationery clip to the spine side.
7. Allow to dry for approximately 2 hours.
Stage 4 - Cutting the cover-cardboard and cover-fabric to size
1. Cut two pieces of cardboard, just slightly bigger than the stack of pages (4mm higher than the pages and 2mm wider than the pages).
2. Cut one piece of cardboard the exact height and width of the the spine of the bundle of pages; this will be the "spine-protector".
3. Cut a rectangular piece of nice-looking fabric for the cover.
Stage 5 - Gluing the spine-protector to the cover-fabric
1. Glue the spine-protector down the centre of the back side of the cover-fabric.
2. Cut out two little "v" shapes from either end of the spine-protector.
3. Glue the remaining flaps of fabric to the spine-protector.
Stage 6 - Attaching the cover-cardboard
1. Cut a strip of plastic from the plastic bag and place it between the front and back pages of the book and the plain fabric that has been glued to the spine. (This is so the pages don't stick to the pieces of cover-cardboard when you glue them in place).
2. Apply glue to half of one side of one of the pieces of cover-cardboard.
3. Line the cover-cardboard up with the spine, and glue it to the piece of plain fabric.
4. Turn over and repeat on the other side.
5. Clamp in place with the stationery clip and allow to dry for approximately 10 minutes.
Stage 7 - Covering the book with fabric
1. Remove the stationery clip and apply a thin layer of glue to the outside of one of the pieces of cover-cardboard.
2. Hold the cover-fabric by the spine-protector in your non-dominant hand.
3. Push the spine-protector firmly against the spine of the book.
4. Smooth the cover-fabric onto the glue on the cover-cardboard. Pull the fabric tight and smooth out any wrinkles.
5. Apply a thin layer of glue to the outside of the other piece of cover-cardboard.
6. Stretch the cover-fabric tightly and smooth it onto the cover-cardboard. Smooth out any wrinkles.
7. Make sure the spine-protector is tightly against the spine. If it is not tighltly against the spine, try and adjust the cover-fabric before the glue dries.
8. Cut two "v" shapes off each corner of the cover fabric.
9. Glue the corner flaps of cover-fabric to the inside of the cover-cardboard.
10. Glue the remaining pieces of cover-fabric to the inside of the cover-cardboard.
11. Place something heavy on top of the book and allow it to dry for approximately 1/2 an hour. (Placing something heavy on top of the book will prevent it from warping as the glue dries).